Boise, Idaho, Sept. 19, 2024 (GLOBE NEWSWIRE) — Idaho Copper Corp. (OTC Pink: COPR) is pleased to announce that it has received initial results from scanning and amenability testwork performed using MineSense XRF scanning technology from representative samples of the three main geological zones at the CuMo Idaho copper-molybdenum-silver deposit. These samples were tested by MineSense at its Vancouver, BC, Canada facility, and involved a series of simulations:
- First, run of mine ore samples from each zone were repeatedly sent (ten times) through the MineSense XRF sensor ATM system, which replicates a mining shovel bucket
- Next, the ore was crushed to <.5 inches and run through a revolving carousel equipped with the same XRF sensors
- Thereafter, each sample was crushed to less than 5 mm and sent again to the carousel for further XRF sensor testwork.
- Finally, the material was coned, quartered and split into 500 gm samples, and then sent to the ALS-Chemex laboratory in Vancouver for typical chemical and ICP analysis (inductive coupled plasma spectroscopy).
The amenability testing and modelling results reported by MineSense are extremely encouraging and demonstrate that (1) the MineSense technology is capable of distinguishing between the different copper and molybdenum grades that can be mined by shovels from the CuMo deposit , and (2) the copper and molybdenum mineralization at CuMo strongly lends itself to ore sorting at the mine face or on belts using XRF sensing technology.
The two graphs below for amenability modelling results show the ability of MineSense XRF shovel-based sensors to delineate between higher and lower grade copper and molybdenum CuMo ore.
These results support separating the metal-bearing veins from the host rock in the CuMo stockwork deposit. Idaho Copper’s plan is to utilize ore sorting to separate a significant portion of run-of-mine waste and lower-grade material immediately after mining, substantially increasing the head grade of the material being fed to the mill.
The Preliminary Economic Assessment (PEA)1 completed in June 2020 by SRK, based on 10-foot sample intervals, concluded that ore sorting would remove 28% of the mined material from mill feed, meaning that 72% of mined material would pass through to the mill. The current XRF analysis indicates that with optimized ore sorting, a marked improvement is possible, with a major portion of the mined material removed prior to sending higher-grade ore for mill processing. The grade enhancement effect for mill feed after scanning and separation of waste and lower-grade material results in a reduction in volume of material routed to the mill and should allow the corresponding mill size to be much smaller than that proposed in the 2020 PEA. This is further projected to yield a significant reduction in capital and overall operating costs.
The grade enhancement effect for mill feed after scanning and separation of waste and lower-grade material results in a reduction in volume of material routed to the mill and should allow the corresponding mill size to be much smaller than that proposed in the 2020 PEA. This is further projected to yield a significant reduction in capital and overall operating costs.
Notes: 1The PEA is preliminary in nature. It includes Inferred mineral Resources that are considered too speculative geologically to have the economic considerations applied to them that would enable them to be categorized as mineral reserves, and there is no certainty that the PEA will be realized. Mineral Resources that are not mineral Reserves do not have demonstrated economic viability. Ore-Sorting is an industry technical term only and does not imply that there is any disclosure of Reserves currently at the CuMo project.
–
The targets and the potential grade enhancements are conceptual in nature as there has been insufficient work done to confirm the target values and it is uncertain that further work would result in realizing these targets.
About Idaho Copper Corporation
Idaho Copper Corporation is a mineral exploration and development company focused on exploring and developing a massive copper-molybdenum-silver deposit in Idaho (United States), (“the CuMo” project). The CuMo project currently consists of one hundred and twenty-six (126) federal unpatented lode mining claims, and six (6) patented mining claims. In total, the project comprises approximately 2,640 acres. The unpatented lode mining claims and patented claims are situated in an unorganized mining district in Boise County, Idaho.
For more information, visit: www.idaho-copper.com.
Safe Harbor Statement
This press release contains forward looking statements which are based on current expectations, forecasts, and assumptions that involve risks and uncertainties that could cause actual outcomes and results to differ materially from those anticipated or expected. These statements are not historical facts but rather are based on the Company’s current expectations, estimates, and projections regarding its business, operations and other similar or related factors. Words such as “may,” “will,” “could,” “would,” “should,” “anticipate,” “predict,” “potential,” “continue,” “expect,” “intend,” “plan,” “project,” “believe,” “estimate,” and other similar or related expressions are used to identify these forward-looking statements, although not all forward-looking statements contain these words. Actual results and the timing of certain events could differ materially from those projected in or contemplated by the forward-looking statements due to a number of factors. Stockholders and potential investors should not place undue reliance on these forward-looking statements. Although the Company believes that its plans, intentions and expectations reflected in or suggested by the forward-looking statements in this report are reasonable, the Company cannot assure stockholders and potential investors that these plans, intentions or expectations will be achieved. These forward-looking statements are not guarantees of future performance and are subject to risks, uncertainties, and other factors, some of which are beyond the Company’s control and difficult to predict and could cause actual results to differ materially from those expressed or forecasted in the forward-looking statements. Except to the extent required by law, the Company has no obligation to update or revise any forward-looking statements, whether as a result of new information, future events, a change in events, conditions, circumstances or assumptions underlying such statements, or otherwise. You are urged to carefully review and consider any cautionary statements and other disclosures, including the statements made under the heading “Risk Factors” in the Company’s Annual Report on Form 10-K for the year ended December 31, 2023, as filed with the Securities and Exchange Commission (the “SEC”) on May 15, 2024, and the Company’s other periodic and quarterly filings with the SEC.
For further information, please contact: [email protected]
- Idaho Copper Corporation
- Idaho Copper Corporation
